Jeep Cherokee Front Brakes Pulsation Problem Repair Guide

Jeep Cherokee Front Brakes Pulsation Problem Repair Guide

Chinaobd2 is a leading supplier of all kinds of Car Diagnostic Tool, Truck Diagnostic Tool, OBD2 Code Reader, Car Key Programmer,ECU Chip Tunning,etc. Currently, the top selling product including: VCDS VAG COM Cable, iProg+ Programmer, Scania VCI3



This article show a guide on how to repair Jeep Cherokee front brakes pulsation trouble guide.It involves the replacement of both front brake rotors and caliper assemblies.

And for more Jeep repair case,check here:Jeep Repair Case,and Jeep Cherokee Trouble Repair.

MODELS:

**1999 – 2002 (WJ/WG) Grand Cherokee (Domestic & International Markets)**

Note: This bulletin applies to wj (domestic market) vehicles built prior to may 11, 2002 (mdh 0511xx), and to wg (international market) vehicles built prior to august 16, 2002 (mdh 0816xx).

Symptom/Condition:

The customer may experience a vibration of the steering wheel, floor, seat, instrument panel, or a minor pedal pulsation (brake roughness) under light to moderate pedal application.This condition may be caused by excessive thickness variation of the brake rotor surface.

DIAGNOSIS:

1.Determine if the front brake vibration/pulsation is caused by excessive thickness variation of either front brake rotor.

2.If excessive thickness variation of the front brake rotor is at fault perform the Repair Procedure.

3.If this bulletin has already been performed, and front brake pulsation/vibration is present, do not perform the Repair Procedure. Investigate other possible cases for front brake pulsation/vibration.

PARTS REQUIRED:

REPAIR PROCEDURE:

1.Raise and support vehicle.

2.Remove both front wheel and tire assemblies.

3.Remove a small amount of brake fluid from the brake master cylinder reservoir with a clean suction gun.

4.Starting with one of the brake/rotor assemblies, bottom the caliper pistons into the caliper by prying the caliper over.

5.Clean the banjo fitting at the end of the brake hose. Remove the brake hose banjo fitting from the caliper. Discard both used banjo copper gasket washers.

6.Remove the two caliper attaching bolts used to secure the caliper mounting bracket (including caliper) to the steering knuckle. Discard the old caliper,mounting bracket, and both attaching bolts.

7.Remove and discard the old brake rotor.

Note: new brake rotors must be used with the new brake calipers.

1 – Hub/Bearing Assembly

2 – Steering Knuckle

3 – Caliper Attaching Bolt Holes And Surface – Clean

4 – Thoroughly Clean Hub Surface Of Rust And Debris

8.Thoroughly clean the surface of the wheel hub/bearing assembly where itmates to the brake rotor. The hub surface must be free of corrosion and dirt so that the new brake rotor rests flush against the hub. This important step will prevent excess rotor lateral runout.

9.Inspect the new brake rotor and its mating surface with the hub/bearing assembly.Install the new brake rotor to the hub/bearing assembly.

10.Using a dial indicator, match mount the brake rotor to the hub/bearing assembly until the minimum lateral runout for the new brake rotor and hub/bearing assembly combination is obtained. This important step will prevent excess rotor runout.

Note: use a dial indicator to insure that minimum lateral runout is achieved for each rotor.

11.Verify that the maximum allowable lateral runout of the brake rotor and hub/bearing assembly combination does not exceed 0.025 mm (0.001 in.). If the lateral runout is in excess of specification then the cause must be determined and corrected before proceeding further with this repair.

12.Inspect the new caliper. Each caliper has a letter “L” or “R” to denote left side or right side of vehicle respectively. Be careful not to dislodge the caliper brake pads and anti-rattle springs when handling the caliper. Remove shipping packing

1 – Caliper Assembly

2 – Caliper-to-Steering Knuckle Attaching Bolt Threaded Holes

3 – Inboard Brake Pad

4 – Anti-Rattle Springs

5 – Outboard Brake Pad

Install the new caliper assembly to a clean steering knuckle mating surface.

14.Install two new caliper assembly attaching bolts (included in front brake package).

Tighten each bolt to 90 – 115 Nm (66 – 85 ft. lbs.).

15.Verify that the brake hose banjo fitting, attaching bolt, and caliper port are clean.

16.Install a new copper gasket washer (included in front brake package) on each side of the brake hose banjo fitting.

17.Using a banjo bolt, attach the brake hose fitting and new copper gasket washers to the caliper.

Note: verify that the brake hose is not twisted or kinked.

Make sure the hose is routed properly.

Tighten the attaching banjo bolt to 31 Nm (23 ft. lbs.)

1 – Anti-Rattle Springs

2 – Letter Denoting Side of Vehicle (“R” = Right Side)

3 – Caliper Slide Bolts

4 – Caliper Bleed Valve

5 – Caliper Assembly

6 – Brake Hose Banjo Fitting, Attaching Bolt, and Copper Gasket Washers

7 – Caliper-to-Steering Knuckle Attaching Bolts

8 – Brake Hose – Route Properly / No Twists or Kinks In Hose

19.Repeat steps 4 to 18 on the opposite side brake caliper assembly.

20.Fill and bleed the brake system. Pump the brake pedal to insure that the front caliper brake pads are seated to the brake rotors. Check brake fluid level frequently.

21.Install both front wheel and tire assemblies. Tighten the front lug nuts to 135 Nm (100 ft.lbs.). This important step helps to prevent warping of the brake rotor(s).

22.Lower vehicle.

23.Verify correct brake fluid level and brake system operation.

This article tech Supported by China OBD2,